Reports.

Parts list.
Attachments.
Granite.

Reports are generated by ArtiCAD based on the current design. To generate a report click on "Reports" and then the name of the report you want to generate. They open up as a text document using your default text editor (normally "Notepad").

The report will be called "report.txt". You may wish to save the file as a different name.

The default text editor can be changed by clicking "Special" - "Edit golobal ini". Click the "Browse" button next to the "Text Editor" box and find the program you wish to use.

NOTE - If you attempt to generate a report and nothing appears, it's possible your default editor is set to a non-existent or invalid program.

Parts list.

The parts list details the units used in the design. The level of detail can be changed by clicking "Reports" - "Configure Parts list" (see below).

A simple parts list example.

Base units
1. 600mm Base Unit
2. 600mm Base Unit
3. 600mm Built Under Oven

Wall units
4. 500mm Wall Unit
5. 500mm Glass Wall Unit
6. 1000mm Chimney Hood

Using the following settings under "Reports" - "Configure parts list":

A fully detailed parts list example.

Base units
1. 600 600mm Base Unit F.H.D., Depth = 600mm, Height = 870mm
    1 X 715mm by 596mm Base Unit Door LHH
2. 600 600mm Base Unit 3D., Depth = 600mm, Height = 870mm
    1 X 140mm by 596mm Base Unit Drawer LHH
    2 X 285mm by 596mm Pan Drawer LHH
3. 600:boh 600mm Built Under Oven, Depth = 600mm, Height = 870mm
    1 X 120mm by 596mm Base Unit Drawer
    1 X Gas Hob
    1 X Single Oven
    1 X Warming Drawer

Wall units
4. 500 500mm Wall Unit, Depth = 300mm, Height = 720mm
    1 X 715mm by 496mm Wall Unit Door LHH
5. 500:g 500mm Glass Wall Unit, Depth = 300mm, Height = 720mm
    1 X 715mm by 496mm Glass Wall Unit Door LHH
6. 1000:ch 1000mm Chimney Hood, Depth = 400mm, Height = 800mm
    1 X Traditional Extractor Canopy

Doors (Standard Doors Shaker unless otherwise stated):
    1 X 715mm by 596mm Base Unit Door LHH
    1 X 120mm by 596mm Base Unit Drawer
    1 X 140mm by 596mm Base Unit Drawer LHH
    1 X 715mm by 496mm Wall Unit Door LHH
    2 X 285mm by 596mm Pan Drawer LHH
    1 X 715mm by 496mm Glass Wall Unit Door LHH

Appliances:
    1 X Gas Hob
    1 X Single Oven
    1 X Traditional Extractor Canopy
    1 X Warming Drawer


Attachments:
BLANKS:

Worktop "Pencil Round Top ":
Edging:
    Total length = 3200;
    Items required = 2; Offcuts left: 2.
Solid: Depth 600:
    Total length = 1800;
    Items required = 1; Offcuts left: 1.

Cornice "Traditional Cornice":
    Total length = 2000;
    Items required = 1; Offcuts left: 1.

Pelmet "Traditional Light Pelmet":
    Total length = 1800;
    Items required = 1; Offcuts left: 1.

Plinth "Plinth":
    Total length = 2960;
    Items required = 1; Offcuts left: 1.


PRE-CUT:

Worktop (solid) 1800 X 600
Worktop (strip) 600 90° 1800 90° 600

Cornice (strip) 300 90° 1000 90° 300

Pelmet (strip) 300 90° 1000 90° 300

Plinth (strip) 530 90° 1800 90° 530

Using the following settings under "Reports" - "Configure parts list":

Configure parts list.

Include code - include the unit code for each item e.g. 600:BOH. See Adding Units - Alternate Method for details.
Include description - include the desciption of the unit e.g. 600mm Built Under Oven.
Include width/depth/height - include the width/depth/height of the item.
Include supplementary info - the short description of the door arrangment e.g. F.H.D for full height door, 3D for three drawers.
Include door details for each unit - add a list of the doors/drawers per unit e.g. 1 X 715mm by 596mm Base Unit Door LHH.
Door details height before width - the default is to display door information width by height.
Include total door details at end - add a seperate list of all the doors and drawers used.
Total door details height before width - the default is to display door information width by height.
Include appliance details for each unit - list the appliance(s) for each unit e.g. 1 X Gas Hob.
Include total appliance details at end - add a seperate list of all the appliances used.
Use only generic description for appliances - even if you use a manufacturer specific appliance, it will be listed with a generic description.
Include attachments - includes the "Attachments" report at the end (in the above example that's everything after "Attachments:"). Can be generated seperately (see "Attachments" below).

Your settings under "Reports" - "Configure parts list" are saved when you exit from ArtiCAD.

The same settings are used when using the parts list when doing a page layout. See Creating page layouts for details.

Return to top.

Attachments.

Generates the list of attachments (worktop, cornice, pelmet etc) used in this design. Identical to the information added to the parts list when "Include Attachments" is selected in "Configure Parts list".

Return to top.

Granite.

For backwards compatibility with previous versions. No longer used.

Return to top.